Wow thanks, mine was in the cart already too.Just wait, I had few major (installation) issues that need to be fix by manufacture (I will post the video if need).
Wait you did this just today?? Did you hook up the oem camera too? Does it still show the Lambo logo?Just installed mine today. Fits & works perfectly. Plugs right in. Jason Burtman hooked me up with a great deal.
Kwan, did you get the back up cam working??My Question to make Factory camera work.
As we know there is a small connector in control module which has 4 wires for the camera (Solid white, Brown, RED and Black).
Do I have to Cut and separate the Solid white and brown from the small connector in control module and then attach RCA cable to send video to CARNAVsytem?
Finally got the RVC diagram and yes Factory camera is working NOW with CarNavSystem(lol).
I would say go ahead and order it. I will make a short clip (video) and post it here (before you get it).
I sent you a message about the alpine speakersI will create a Clip for the factory cam as well.
In the mean time, if you guys trying to use the Factory CAM, make sure to order following relay. You just need one, I ordered 5 because I couldn't find better deal (and I will find the use for rest of them in some other project - lol).
I did actually installed Alpine SPR-60C 6.5" (did some custom work to install - lol). I will add Sub and Amp in future.
I have another set of Alpine SPR-60C 6.5" (open Box) if someone need it let me know. I purchased set from Best-buy outlet for around $105. I can probably put a Relay as well since I have few extras.
The RVC diagram just incase...
O'man... Another Cheaper RADIO for $289.99
Anyone want to try this and make it work? (Not me, I got mine working after all-o-that pain - lol)
watching, like plug n playThat’s totally doable if we had both a male and female end of both connectors on the backup camera module. The cigarette lighter connection can be made with spade connectors, both male and female.
Sent from my iPhone using Tapatalk
After hours exploring wires i found that my RNSE catchs the reverse camera's video signal directly i thing.
On the 32 pins RNSE's connector :
Pin # 15 in sync (black wire)
Pin #16 in G (green wire)
Pin# 31 in B ( blue Sky wire)
Pin #32 in R (red wire)
Pin #30 RGBS in gnd (black wire)
Pin #27 NC (purple wire)
On the "C" connector (green) on the RNSE :
Pin #2 RFSL (white/green wire)
When reverse Gear or manual camera's switch :
RFSL is 12v (i think it's to Switch/activate the screen on the camera's entry/source)
Ground and "in sync" are 3.84v (connector not connected to the RNSE. If it's connected to the RNSE i have 1.84v)
I have disconneted the purple and all is working without it...don't know what this wire does perhaps a shield
So i think i need a RGB converter to RCA...
Here is a picture of my RNSE 32 pins connector
On the harness we Can see others wires not used (a Brown, a white,a shield i think and a pink and grey wires)
Wires were like that After removing the heat shrink and the tape...i haven't cutted them.. strange work hummm)
Perhaps are they RCA vidéo signal....i don't know...
Envoyé de mon SM-A405FN en utilisant Tapatalk
The connection that goes from the cigarette lighter across 86-87 to the purple wire on the back of the head unit.
Black/red wire from backup power goes to pin 30 or 85 of the relay to trigger the relay.
I've sold quite a few of these radio's to forum members. IF anyone is looking for one, call or text me at 717-319-2100, etc.
Now. Here's the big question. Has anyone figured out how to jailbreak one of these yet? IF so, I'm working with one of my current customers who has some very cool ideas where we can use this radio to control other things in the car....
These are not easy, I've screwed up two of these so far with no end in sight! I just could not get the bubbles out of the darn thing!Update: The screen scratches quite easily on this unit. I ordered a 2-pack from Amazon for screen protectors in an anti glare matte finish.
Matte Screen Protector from Amazon and the size we need is 5.97" by 3.36"